Ruijie RG-N18000-X Series Switch RGOS11.3(1)B9 Firmware
Please rate this document.
Please leave your suggestions here.
200 characters leftIf Ruijie may contact you for more details, please leave your contact information here.
* I understand and agree to Terms of Use and acknowledge Ruijie's Privacy Policy.
Thank you for your feedback!
B9%20V2.0.files/image006.jpg)
B9%20V2.0.files/image007.gif){kind=small}
Contents
This document includes the followingsections:
Basic Information
Table 1 lists the basic information of thecurrent release.
Table 1 Basic Information of the CurrentRelease
| N18000-X_RGOS11.3(1)B9 | |
| Previous Release | N18000-X_ RGOS 11.3(1)B4 |
| Applicable Product | RG- N18018-X, RG-N18010-X |
| Category | Official release |
Use the show version command todisplay information about the software version.
dut2#shoversion
Systemdescription : Ruijie High-density IPv6 100G CoreRouting Switch(N18010-X) By Ruijie Networks
Systemstart time : 2034-04-25 06:42:06
Systemuptime :14:17:50:31
Systemhardware version : 1.10
Systemsoftware version : N18000-X_RGOS 11.3(1)B9
Systempatch number : NA
Systemserial number : G1L2057000400
Systemboot version : 1.2.22
Moduleinformation:
Slot M1 : M18000X-CM II
Hardware version : 1.10
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : G1L2057000400
Slot 1 : M18000X-12QXS12CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570028
Slot 2 : M18000X-18QXS18CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570020
Slot 3 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570014
Slot 4 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570023
Slot 5 : M18000X-48XS2CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570015
Slot 6 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : 1234942570017
Slot FE1 : M18010X-FE-C I
Hardware version : 1.00
Boot version : 1.2.22
Software version : N18000-X_RGOS 11.3(1)B9
Serial number : G1KS83Q000065
dut2#shover detail
Systemdescription : Ruijie High-density IPv6 100G CoreRouting Switch(N18010-X) By Ruijie Networks
Systemstart time : 2034-04-25 06:42:06
Systemuptime :14:17:50:54
Systemhardware version : 1.10
Systemsoftware version : N18000-X_RGOS 11.3(1)B9
Systempatch number : NA
Systemsoftware number : M01411508242017
Systemserial number : G1L2057000400
Systemboot version : 1.2.22.917a8a0(160718)
Systemcore version : 2.6.32.cc45751d6ca85d
System cpupartition : 8-31
Moduleinformation:
Slot M1 : M18000X-CM II
Hardware version : 1.10
Boot version : 1.2.22.917a8a0(160718)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M01411508242017
Serial number : G1L2057000400
Slot 1 : M18000X-12QXS12CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570028
Slot 2 : M18000X-18QXS18CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570020
Slot 3 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570014
Slot 4 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570023
Slot 5 : M18000X-48XS2CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570015
Slot 6 : M18000X-6QXS6CQ-CB
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Software number : M00455908242017
Serial number : 1234942570017
Slot FE1 : M18010X-FE-C I
Hardware version : 1.00
Boot version : 1.2.22.69aa19a(160612)
Software version : N18000-X_RGOS 11.3(1)B9
Softwarenumber : M00455908242017
Serial number : G1KS83Q000065
Hardware Supported
Table 2 shows the hardware supported bythe RGOS 11.3(1)B9.
Table 2 Supporting Hardware Models
| Hardware Model | Version | Description |
| RG-N18018-X | 1.0 | Chassis |
| RG-N18010-X | 1.0 | Chassis |
| M18000X-CM II | 1.0 | Supervisor module |
| M18018X-FE-C II | 1.0 | Switch fabric module |
| M18010X-FE-C I | 1.0 | Switch fabric module |
| M18000X-48XS2CQ-CB | 1.0 | Line card |
| M18000X-6QXS6CQ-CB | 1.0 | Line card |
| M18000X-12QXS12CQ-CB | 1.0 | Line card |
| M18000X-18QXS18CQ-CB | 1.0 | Line card |
| M18000X-48XT2CQ-CB | 1.0 | Line card |
| RG-PA2700I | 1.0 | Power supply module |
B9%20V2.0.files/image002.jpg){kind=small}
The hardware version number is rounded to thefirst decimal place. The numeral in the second decimal place does not changethe supporting release.
For detail, see RG-N18000-X Series SwitchHardware Installation and Reference Guide V1.13.
Resolved Issues
This section describes the fixed bugs.
Table 3 Fixed Bugs Based on 11.3(1)B9
| No. | Bug Description |
| 1 | When BGP/BFD/ a great number of routes are configured, one-key upgrade causes traffic interruption for 113s. |
| 2 | High CPU usage may cause an incorrect temperature of the line card displayed in the output of the show temp command. |
| 3 | Frequent flapping of ECMP routes may cause failure to ping some neighbors. |
| 4 | Occasional suspending of the bridge thread on the supervisor module may cause service interruption. |
| 5 | If BGP enables multiple VRF instances, the downlink neighbor may be restarted, and traffic interruption may occur occasionally for several seconds. |
| 6 | The clear ip ospf process command causes BFD flapping. |
| 7 | If an inactive default route exists, when the outbound interface is down, BGP route convergence is slow. |
| 8 | If a recursive query shows that the next route of the BGP route is an IGP route, and an active default route exists, when IGP goes up and down, the NSM process occasionally restarts. |
| 9 | When a 40 Gbps copper cable is connected to a 100 Gbps port, error information is displayed. |
| 10 | When the physical port of the active chassis in a VSU is down, an active/standby switchover is immediate performed and may cause an incorrect state of the new physical port. |
| 11 | When CPU usage of the supervisor module is high, if a line card is started in hot startup mode, ports on the line card may fail to go up. |
| 12 | When a VSU is restarted, ports on the panel may fail to go up and be enabled at a low probability. |
| 13 | When the VSL card is restarted after the AP is switched to a larger-capacity mode, ports on the standby switch may fail to be pinged at a low probability. |
| 14 | When an ACL applies to the outbound direction of an SVI, restarting the SSC process or the reloaded device may fail to take effect. |
| 15 | When you configure an enhanced load-balancing template L2 or IPv4/IPv6 source port factor, and change the hash mode from non-enhanced to enhanced, ECMP fails to perform load balancing based on the source port. |
| 16 | After modifying the AP mode, you need to manually restart the AP twice to use it properly. |
| 17 | If a line card is started in hot startup mode when the system is busy, data synchronization may fail to be triggered, and ports cannot go up. |
Changed Features
Table 4 HardwareChange
| Hardware Model | Version Number | Description |
| M18000X-6QXS6CQ-CB | 1.0 | Line card is supported |
| M18000X-12QXS12CQ-CB | 1.0 | Line card is supported |
| M18000X-18QXS18CQ-CB | 1.0 | Line card is supported |
| M18000X-48XT2CQ-CB | 1.0 | Line card is supported |
Table 5 New Feature
| Module | VSU |
| New Feature | VSU on N18010-X |
| CLI Change | N/A |
| Web Change | N/A |
| MIB Change | N/A |
Related Documentation
n RG-N18000-X Series Switch RGOS ConfigurationGuide, Release 11.3(1)B9
This manual describes the various network protocols and their implementationprinciples for the RG-N18000-X series with the detailed configuration examples.
n RG-N18000-X Series Switch RGOS CommandReference, Release 11.3(1)B9
This manual describes the configuration commands related to the various networkprotocols supported on the RG-N18000-X series switch RGOS11.3(1)B9 version in detail, including thecommand mode, parameter description, usage guide, and configuration examples.
You can obtain the related documents at: http://www.ruijienetworks.com/.
Upgrade Files
Table 6 LatestUpgrade Firmware
| Applicable Model | Upgrade Firmware | File Size | MD5 |
| M18000X-CM II | N18000-X_RGOS11.3(1)B9_CMXII_install.bin | 211,173,195 bytes | 480f6e699499d3133f442d9481907bcd |
Upgrade Tips
The following are some tips for upgradingthe RG-N18000-X Series Switch RGOS 11.3(1)B9:
n During the upgrade and downgrade, pay attentionto the prompt messages. If failures occur, please save the log and contact usfor technical assistance.
n During the upgrade and downgrade, it isrecommended you not power off or reset the system, or plug/unplug any module.
n Use the show version command to check thefirmware after the upgrade/downgrade.
