Back

Compare Products

Hide

Clear All

VS

Home> Support> Downloads>

Ruijie RG-M8600E-WS-ED Wireless Controller RGOS11.9(5)B1 Firmware

2019-12-03 View:
RG-WLAN Series Wireless Controllers RGOS Release Notes, 11.9(5)B1

 

 

 

 

 

Ruijie RG-WLANSeries Wireless Controllers RGOS Release Notes, 11.9(5)B1

 

 


Release Date: Dec. 3rd, 2019

 

 

 

 



Contents

This document includes the following sections:

n Basic Information

n Hardware Supported

n New Features

n Resolved Issues

n Upgrade Packages

n Upgrade/Downgrade Tips

Basic Information

Table 1 lists the basic information of the current release.

Table 1 Basic Information of the Current Release

Current Release

RGOS 11.9(5)B1

Previous Release

RGOS 11.9(4)B1

Applicable Product

c series : WS6108, WS6008

d series: WS6816

e series: M8600E-WS-ED, M18000-WS-ED

Category

Official release

 

Use the show version command to display information about thesoftware version.

WS6108#showversion detail

Systemdescription      : Ruijie 10G WirelessSwitch(WS7208-A) By Ruijie Networks.

Systemstart time       : 2019-12-08 14:45:43

Systemuptime           : 0:02:23:10

Systemhardware version : 1.00

Systemsoftware version : AC_RGOS 11.9(5)B1, Release(06240614)

Systempatch number     : NA

Systemsoftware number  : M14093512062019

Systemserial number    : H1MB0GY000755

Systemboot version     : 3.3.1.b0cc174(191018)

Systemcore version     : 4.4.52.b2016415ca22fe

System cpupartition    : 1-3

Release Number Description

Software number M20015609252015 indicates 20:01:56 on September 25,2015.

*    1) Release number is formatted as AABBCCDD. 2) AA indicates year. 01stands for 2014, 02 for 2015 and so on. 3) BB indicates month. 13 stands forJanuary, 14 for February and so on. 4) CC indicates date. 5) DD indicates timein 24-hour format, e.g., 16 stands for 4pm.

Take release number 02212520 for example. It indicates 8pm onSeptember 25, 2015.

Hardware Supported

Table 2 shows the hardware supported by the RGOS 11.9(5)B1.

Table 2 Supporting Hardware Models

Hardware Model

Version

Description

WS6008

1.1x, 1.2x, 1.5x, 2.0x

8 1000BASE-T ports, 2 1000BASE-T/1000BASE-X ports (combo)

WS6108

1.0x, 1.1x

8 1000BASE-T ports, 2 1000BASE-T/1000BASE-X ports (combo)

WS6816

1.0x, 1.1x

8 1000BASE-T/1000BASE-X ports (combo), 4 1G/10GBASE-X SFP+ ports, Expansion to 16 1000BASE-T/1000BASE-X ports (combo) or 8 1G/10GBASE-X SFP+ ports

M8600E-WS-ED

1.0x, 1.1x, 2.0x

WS Series Wireless Controller Module for RG-S8605E/S8607E/S8610E Switch, 128 APs License by default, Up to 2,560 Indoor APs or 4,000 Wall APs License

M18000-WS-ED

1.0x, 1.1x, 2.0x

WS Series Wireless Controller Module for RG-N18000 Switch, 128 APs License by default, Up to 2,560 Indoor APs or 4,000 Wall APs License

 

*     The hardware version number is rounded to thefirst decimal place. The numeral in the second decimal place does not changethe supporting release.

New Features

RRM 2.0 Supporting Group-based Network Optimizing

Description

RRM 2.0 supports group-based network optimizing to:

1. set the scheduled time;

2. trigger automatic RF adjustments;

3. enable RRM 2.0 features.

CLI command

Run the rrm [ 2.4g | 5g ] appoint date time [ ap-group group-name ] command to set the reservation time based on AP group.

Run the rrm [ 2.4g | 5g ] update [ ap-group ap-group ] [ channel | txpower ] command to manually trigger auto RF adjustments.

ACs Supporting MACC

Description

MACC is accessible to ACs. So, ACs upload to MACC AC data (information about system, interfaces, dial-up ports, and WAN/LAN ports, syslog and key configuration changes), AP data (online and offline events, lists of connected APs, running status, and key property changes), and STA data (online and offline events, lists of connected STAs, IP change notifications, roaming log and running status).

*    Uploading information of dial-up and WAN/LAN ports is supported on multi-functional ACs.

CLI command

N/A

Configuring Internal PortalAuthentication on the Web Page of Multi-Functional ACs

Description

On a multi-functional AC, you can configure internal portal authentication on EWEB. And logo customization is supported on the Portal authentication page.

CLI command

N/A

APs Supporting DFS

Description

DFS is supported on APs with versions of 11.9(4)B1 and 11.1(9)B1P18.

CLI command

Run the show dfs adjustment-channels [ ap-name ] command to display hopping channels and bandwidth of one or all APs.

Run the show dfs non-occupancy-channels [ ap-name ] command to display the list of non-occupancy radar channels of one or all APs.

Run the show dfs historical-radar-channels [ ap-name ] command to display historical information of radar channels of one or all APs.

Supporting a Privileged VLAN

Description

A privileged VLAN can be configured, so only packets from this VLAN are forwarded while packets from other VLANs are dropped. However, packets from other VLANs are forwarded when there are no packets from the privileged VLAN for 60 seconds.

CLI command

Run the vlan-first global-enable command to enable the VLAN-first function.

Run the vlan-first vlan [vian-id] command to configure the privileged VLAN.

Run the vlan-first ip [sip] [dip] command to configure the multicast address for the privileged VLAN.

ACs Supporting SSH Clients

Description

SSH clients are supported on ACs.

CLI command

N/A

Network Monitoring System Probing STA Information

Description

STA information is probed by the network monitoring system.

CLI command

Use the web-server enable api-path probe-sta syslog command to print STA syslog. And run the sta-logging mac-fmt-line command to print syslog when STAs get online and obtain IP addresses.

ACs Assigning BIN Files to APs

Description

After losing its BIN file, an AP sends requests to the AC for a BIN file. Then, the AC searches its storage and finds a matched BIN file before assigning it to the AP for upgrade. If there is no matched BIN file stored on the AC, it is automatically recorded into the EWEB alarming system, so notifications are sent to the network administrator on the EWEB page.

CLI command

N/A

Improved Max User Capacity of Satellite APs

Description

Max user capacity is improved for satellite APs. This improvement is accessible in scenarios where latest versions are applied to ACs, APs and satellite APs.

CLI command

N/A

All Models Supporting License 1

Description

License 1 is supported on all models.

CLI command

N/A

Resolved Issues

Table 3 shows the fixed bugs based on RGOS11.9(5)B1.

Table 3 Fixed Bugs

No.

Bug Description

1

Deleting one association group on the WEB page caused the removal of all groups.

2

An error message appeared after WLANs were added and network time was disabled.

3

In WPA2 encryption + MAB authentication +WEB authentication mode, users were notified of password error during first connection attempt.

4

In a VAC scenario, APs got online and offline on a frequent basis, leading to disconnection of more than 900 APs.

5

On the WEB page of the AC, an online AP was wrongly displayed in the default group and its status was shown as offline.

6

It took too long for the enable command to take effect.

7

The OID node 1.3.6.1.4.1.4881.1.1.10.2.81.2.3.1.1 was incorrect.

8

SCC entries were removed if local forwarding users switched between two RF cards of an AP.

9

On the WEB page, notes about usernames were lost on blacklists and whitelists.

10

Configuring logging vlan 6 triggered NFPP ARP protection, which caused device to reboot.

11

On the WEB page of the AC, if the IP address of an AP was changed, the AP could not get online normally.

12

Failure occurred in STA association.

13

Exceptions occurred in STA authentication.

14

Downstream rates read on the SNC greatly exceeded the rate limit set on the AC.

15

For an online AP, SNC wrongly alarmed its disconnection, so all of its STAs were disconnected.

16

When the device came up, the default audit policy did not take effect.

17

Behavior policy matching failed.

18

In a VAC system, the time zone of the master AC failed to be modified, and the rootfs partition was running out of space.

19

MIB readme was inconsistent with the code.

20

In a VAC system, after an AP resumed connection, a message about MAC address conflicts appeared on the WEB page of the AC.

21

On the WEB page, only the first page was displayed when users chose to view entries based on both the entry number and signal strength.

22

The configuration did not come into force that a maximum of 50 IP addresses of authentication-exempted users were shown on the WEB page.

23

The whitelist containing more than 280 entries failed to be imported.

24

The wbs_ctl process restarted when a MacBook Pro running OS Catalina 10.15 switched its association between a WAP3-encrypted SSID and an open SSID.

25

In an MACC scenario, when a large number of APs connected to the AC, the cloud-diagnosis.elf process kept restarting.

26

In a VAC scenario, if a great quantity of APs connected to the AC and RRM 2.0 network optimizing was enabled, insufficient buffer capacity led to message synchronization failures between the master and standby ACs.

27

In ap-group mode, the statistics of online radio was wrong, not reflecting the actual number.

Upgrade Packages

Table 5.1 WS6008/WS6108

Applicable Product

File

File Size

MD5

WS6008 v1.1x, v1.2x, v1.5x, v2.0x

WS6108 v1.0x, v1.1x

AC_RGOS11.9(5)B1_G2C6-01_06240613_install.bin

54,159,031 bytes

90a9b0504ac8544dfadfe262c8eb639e

Table 5.2 WS6816

Applicable Product

File

File Size

MD5

WS6816 v1.0x, v1.1x

AC_RGOS11.9(5)B1_G2C6-02_06240613_install.bin

57,600,383 bytes

e28b0baf21a69a4e2dc340a748e40951

Table 5.3 M8600E-WS-ED / M18000-WS-ED

Applicable Product

File

File Size

MD5

M8600E-WS-ED v1.0x, v1.1x, v2.0x

M18000-WS-ED v1.0x, v1.1x, v2.0x

AC_RGOS11.9(5)B1_G2C6-03_06240613_install.bin

56,704,070 bytes

0631e3f3c79a4b53e597ad13800d7499

Upgrade/DowngradeTips

The following are some tips for upgrading the RG-WLAN Series WirelessController RGOS 11.9(5)B1:

n  Usethe show version command to check the current firmware beforeupgrade/downgrade. Select proper upgrade/downgrade mode according to thecurrent firmware and the target firmware.

n  Duringthe upgrade and downgrade, pay attention to the prompt messages. If failures occur,please save the log and contact us for technical assistance.

n  Duringthe upgrade and downgrade, it is recommended you not power off or reset thesystem, or plug/unplug any module.

n  Usethe show version command to check the firmware after the upgrade/downgrade.

 

How do you like this document ?

Suggestion


(0/255)

Can we contact you to discuss your suggestion?

Privacy Policy
Thank you. We will inform you of our response as soon as possible.
Thank you again for your valuable input!
This page will be closed in 5 s…
Submit
Document Questionnaire
We sincerely invite you to fill in this questionnaire on Ruijie document acquisition and user experience.
No
Yes

Ruijie Networks websites use cookies to deliver and improve the website experience.

See our cookie policy for further details on how we use cookies and how to change your cookie settings.

Cookie Manager

When you visit any website, the website will store or retrieve the information on your browser. This process is mostly in the form of cookies. Such information may involve your personal information, preferences or equipment, and is mainly used to enable the website to provide services in accordance with your expectations. Such information usually does not directly identify your personal information, but it can provide you with a more personalized network experience. We fully respect your privacy, so you can choose not to allow certain types of cookies. You only need to click on the names of different cookie categories to learn more and change the default settings. However, blocking certain types of cookies may affect your website experience and the services we can provide you.

  • Performance cookies

    Through this type of cookie, we can count website visits and traffic sources in order to evaluate and improve the performance of our website. This type of cookie can also help us understand the popularity of the page and the activity of visitors on the site. All information collected by such cookies will be aggregated to ensure the anonymity of the information. If you do not allow such cookies, we will have no way of knowing when you visited our website, and we will not be able to monitor website performance.

  • Essential cookies

    This type of cookie is necessary for the normal operation of the website and cannot be turned off in our system. Usually, they are only set for the actions you do, which are equivalent to service requests, such as setting your privacy preferences, logging in, or filling out forms. You can set your browser to block or remind you of such cookies, but certain functions of the website will not be available. Such cookies do not store any personally identifiable information.

Accept All

View Cookie Policy Details

Contact Us

Contact Us

How can we help you?

Contact Us

Get an Order help

Contact Us

Get a tech support