Back
Home> Support> Technical Documents>

Ruijie RG-EG Implementation Cookbook (V1.0)

2020-02-15 View: 10037
Catalog
11.x项目配置指南模板

       EG Quick Start

3.1       EG2100-P Quick Start Guide

3.1.1      Setup via EG local Web 

1) Modify the IP address of PC.

         IP address: 192.168.1.x (except 192.168.1.1)

         Subnet mask: 255.255.255.0

         Default gateway: 192.168.1.1 (default LAN IP)

2) Connect the PC to any port (except WAN0) on the device.

3) Visit http://192.168.1.1 by Chrome browser.

4) Enter the username and password on the login page and click “Log In”.

Default Username: admin

Default Password: admin

5) Change the password at the first login.

Select a scenario.

Configure the WAN port (DHCP, Static IP or PPPoE).

It is not recommended to change the IP of LAN port; otherwise, you may need to log in and configure again. After wizard completes, you can configure LAN port on the interface configuration page.

 

6) Click Dashboard to open the homepage, or click Interface to enter the interface configuration page. If the WAN port is connected to the Internet, you can access the Internet now and add the EG to the Cloud.

3.1.2      Setup via Mobile App (Recommended)

3.1.2.1      Configure WAN Uplink Port

1) Connect AP710 to any of LAN1-LAN7 ports on EG2100-P. After AP is powered on, it will broadcast the default SSID: RJ-xxxxxx (xxxxxx is the last six digits of EG2100-P SN).

2) Launch Ruijie Cloud App, tap Tool menu, and tap Gateway Setup to start the Gateway Quick Setup, as shown below:

3) Log in with the default account (username: admin, password: admin).

    

      

4) Reset the Web management password, and tap Next (Note: This password is required when you add EGs by scanning the QR-code).

 

5) Select a Scenario. If you select the S&M Enterprise, Flow Control Configuration will be added to the wizard. Here you can just tap Next to enter the Interface settings.

 

6) Configure the WAN port (PPPoE, Static IP or DHCP), tap Next and wait for about 5 seconds until a success message is displayed. (Note: After the message is displayed, EG will restart).

 

7) The initial configuration complete. Now you can create the network and add devices on App.

3.1.2.2      Add Network and Device

1) Open the Ruijie Cloud App, tap Create Network, and enter the network name and SSID.

 

 

2) After the network is created, enter the network and tap Add Device to add AP and EG2100-P by scanning the QR code (AP SN/MAC) on the back of the device. (Note: When adding an EG, you need to enter its Web management password.)

 

  

3) Wait for about 3 to 5 minutes, and you can see the online status of AP and EG devices.

The SN/MAC QR-Code demo on the back of AP:

3.1.2.3      Access EG Web from Cloud

1) After an EG comes online on the Ruijie Cloud, you can visit its eWeb page for advanced configuration. Select the EG in the Gateway List, and click eWeb.

2) After the tunnel is created, the Web management page will open automatically, as shown below:

3) If the following information is displayed, click Proceed to enter the eWeb system.

3.2       EG3000 Series Quick Start Guide

3.2.1      WAN Uplink Quick Setup

1) Modify the IP address of PC.

         IP address: 192.168.1.x (except 192.168.1.1)

         Subnet mask: 255.255.255.0

         Default gateway: 192.168.1.1 (default LAN IP)

2) Connect the PC to any port (except WAN0) on the device.

3) Visit http://192.168.1.1 by Chrome browser.

4) Enter the username and password on the login page and click “Log In”.

Default Username: admin

Default Password: admin

5) Change the password at the first login.

Select a scenario.

Configure the WAN port (DHCP, Static IP or PPPoE).

It is not recommended to change the IP of LAN port; otherwise, you may need to log in and configure again. After wizard completes, you can configure LAN port on the interface configuration page.

 

6) Click Dashboard to open the homepage, or click Interface to enter the interface configuration page. If the WAN port is connected to the Internet, you can access the Internet now and add the EG to the Cloud.

3.2.2      Add Device to Ruijie Cloud

1) Open the Ruijie Cloud App, tap Create Network, and enter the network name and SSID.

 

 

2) After the network is created, enter the network and tap Add Device to add AP and EG3250 by scanning the QR code (AP SN/MAC) on the back of the device (Note: There is no QR code behind EG3000UE/XE, so please manually enter SN). When adding an EG, you need to enter its Web management password.

 

  

3) Wait for about 3 to 5 minutes, and you can see the online status of EG device.

The SN/MAC QR-Code demo on the back of EG:

 

3.2.3      Access EG Web from Cloud

1) After an EG comes online on the Ruijie Cloud, you can visit its eWeb page for advanced configuration. Select the EG in the Gateway List, and click eWeb.

2) After the tunnel is created, the Web management page will open automatically, as shown below:

3) If the following information is displayed, click Proceed to enter the eWeb system.

 

 

Ruijie Networks