Home> Products> Wireless > Indoor Access Point Series>

RG-AP130(W2) Wireless Access Point Series

Ruijie RG-AP130(W2) Wall AP is designed for wireless deployment in hotels, offices, residential buildings and settings alike. The wall-mountable AP has the same size as a standard 86-type faceplate with integrated Ethernet and voice ports. Featuring a concise design and easy deployment, the AP enables zero disruption to the interior finishes and offers the best solution for scenarios with delicate interior design.

The dual-radio, dual-band AP supports concurrent operation of 802.11a/n/ac and 802.11b/g/n. The RG-AP130 (W2) equipped with the advanted Wave 2 RF chip, supports the feature of MU-MIMO and improves the user experience for concurrent access. RG-AP130(W2) provides 4 1000Mbps or 100Mbps RJ-45 ports and 1 RJ-45 Voice/PoE pass-through port (RJ-11 combo), delivering optimal wireless network coverage and cost protection with additional wired network interfaces and voice ports.

Feature Highlights:

●RG-AP130(W2) IEEE 11ac Wave 2 Ready

●Fast and Easy WiFi Deployment

●Reuse Existing Cabling Structure for Investment Protection



High-performance 802.11ac Wall AP

The Ruijie RG-AP130(W2) Wall AP adopts a dual-radio, dual-band design and supports concurrent operation of 802.11a/n/ac and 802.11b/g/n. RG-AP130(W2) provides 4 1000Mbps or 100Mbps RJ-45 ports and 1 RJ-45 transparent Voice/PoE pass-through port (RJ-11 combo). The AP on the rear also offers 1 1000Mbps uplink port and 1 RJ-45 transparent pass-through port (RJ-11 combo). The dual-band 2.4G and 5G coverage can achieve a concurrent coverage supporting 2 spatial streams, providing an unparalleled network experience.

MU-MIMO Support

The wall-mountable RG-AP130(W2) supports the MU-MIMO feature. Most single-stream end devices only utilize half of the resources of the dual-stream RG-AP130(W2) Wall AP with the other half left unused. The wasted AP resources will stagnate the enhancement of user experience. With the MU-MIMO feature, RG-AP130 (W2) makes full use of the AP resources and is capable to serve two end devices concurrently, improving the user experience.

Easy and Fast Deployment

The RG-AP130(W2) Wall AP adopts a wall-mounted design with 2-step easy deployment:

Step 1: Remove the original 86-type faceplate from the wall.

Step 2: Directly install the plug-and-play Wall AP and connect with original UTP cable (PoE).

This breaks through traditional wireless network construction methods by reusing existing network cables and minimizes the impact of network construction on hotel or similar settings. As no additional cabling is required, the Wall AP delivers maximum business agility and investment protection. Ruijie also offers a wide range of optional accessories to meet your unique deployment needs.

Traditional challenges on laying additional cabling for AP installation

Full Signal Coverage

Traditional Aps are installed in corridors and the indoor network signals are weak or even completely degenerated after wall penetration. The RG-AP130 Wall AP, on the other hand, can be installed inside the room and hence ensures full coverage anywhere for the best user experience of voice, video or Internet browsing.

Unified Management of FAT and FIT Modes

The RG-AP130 Wall AP supports both FAT and FIT AP modes, which can be flexibly selected as desired. The Wall AP allows easy upgrade of WLAN to a large-scale network, fully protecting users’ investment costs. In the hotel scenario, the deployment involves a large number of guest rooms and so is the amount of Aps. AP management of such a large scale is what current hospitality solutions struggle to guarantee. The RG-AP130 Wall AP offers a simple and easy solution to lessen administrator workload. Teaming up with Ruijie’s Wireless Access Controllers series, the solution enables centralized AP management and fast troubleshooting. Comparing with traditional SOHO Aps, the RG-AP130 Wall AP greatly facilitates O&M personnel to manage the whole wireless network.

Comprehensive Security Protection

●Industry-leading Double Security Designs

The RG-AP130 Wall AP is manufactured using qualified ABS+PC materials, offering superior shock, pressure and temperature resistance for secure deployment. The specially designed screw protects the AP from malicious damage or theft. The Wall AP and color case also guard against theft with a unique security key. The administrator can manage all the Aps using one security key with ease.

User Access Control

The RG-AP130 Wall AP supports a broad library of user authentication methods such as Web, 802.1x, MAC address, and local authentication for customers’ choice. It also supports Ruijie’s end-to-end BYOD (Bring Your Own Device) Solution, complies with a standard access control system, and strictly defines access control policies in terms of user access, authorization, host compliance check, network behavior monitoring, and network threat defense. All these control measures ensure that users are authenticated before accessing a network and securely enjoy network services.

Full Security Protection

Teaming up with Ruijie’s integrated network management system RG-SNC (Smart Network Commander) and RG-WS Wireless Access Controller Series, the Wall AP delivers outstanding security features including Wireless Intrusion Detection System (WIDS), RF interference location, rogue AP countermeasures, anti-ARP spoofing, and DHCP.

Multiple Easy-to-use Authentication Modes

As the key components of Ruijie’s intelligent cloud-based RG-MACC platform, the RG-AP130 Series offers secure and optimal network connections that are required in various scenarios. The RG-AP130 Series supports convenient and high-efficiency Protected Extensible Authentication Protocol (PEAP), web portal authentication, SMS authentication, and voucher (QR code) authentication.

Voucher (QR code) authentication is another wireless security highlight, enabled by Ruijie’s RG-MACC-SAM platform, which generates one-time or pay-per-use vouchers in recurring or one-time format with time-based policies, streamlining and simplifying the generation and management of QR code or voucher. 


Advanced Guest Interfaces of the QR Code Authentication




Target Deployments

For wireless deployment in hotels, offices, residential buildings

Basic Specifications


Concurrent dual-radio dual-band


802.11a/b/g/n/ac, Wave 2

Operating Bands

2.4GHz and 5GHz


Built-in omnidirectional antenna


Antenna Gain


Max Throughput



1.167Gbps per AP

 Spatial Streams



DSSS:CCK@5.5/11Mbps, DQPSK@2Mbps, DBPSK@1Mbps

OFDM:64QAM@48/54Mbps, 16QAM@24Mbps, QPSK@12/18Mbps, BPSK@6/9Mbps



Receiver Sensitivity




11ac HT20:-90dBm(MCS0), -65dBm(MCS8)

11ac HT40:-85dBm(MCS0), -60dBm(MCS9)

11ac HT80:-82dBm(MCS0), -58dBm(MCS9)

Maximum Transmit Power

≤100mW (20dBm, transmit power of the RF card only)

IP Rating



Service Port


4 10/100/1000M Ethernet ports


1 RJ-45 port  (RJ-11 combo)


 1 10/100/1000M uplink port

 1 RJ-45 pass-through port (RJ-11 combo)

Management Port

1 console port (Micro USB)


Power Supply

PoE (802.3af), local DC power supply

Power Consumption



Maximum clients per AP

Up to 32

BSSID capacity

Up to 8 per radio

Up to 16 per AP

SSID hiding


Configuring the authentication mode. Encryption mechanism and VLAN attributes for each SSID


Remote Intelligent Perception Technology (RIPT)




Intelligent  load balancing based on the number of users or traffic


STA control


Bandwidth control

STA/SSID/AP-based speed control

Preference for 5GHz (band select)


Wireless position tracking


Dynamic Frequency Selection(DFS)

Future release support


PSK, Web, and 802.1x authentication


Data encryption

WPA (TKIP), WPA2 (AES), WPA-PSK, and WEP (64 or 128 bits)

QR code authentication


SMS authentication


PEAP authentication


Data frame filtering

Whitelist, static/dynamic blacklist

User isolation


Rogue AP detection and countermeasure


Dynamic ACL assignment




CPU Protection Policy (CPP)


Network Foundation Protection Policy (NFPP)


Wireless Intrusion Detection System(WIDS)


Wireless Intrusion Prevention System (WIPS)



Ipv4 address

Static IP address or DHCP reservation



Ipv6 address


Ipv6 tunnel


Ipv6 transparent transmission



Multicast to unicast conversion

Management and Maintenance

Network management

SNMP v1/v2C/v3, Telnet, TFTP, FTP and Web management

Visualized wireless heat map analysis


(need to integrate with SNC)Support

Real-time spectrum analysis


(need to integrate with SNC)Support

Fault detection and alarm


Cloud AC management


Statistics and logs


FAT/FIT switching

The AP working in FIT mode can switch to the FAT mode through the RG-WS wireless AC.

The AP working in FAT mode can switch to the FIT mode through a local console port or Telnet.

External Characteristics


Standard: Anti-theft screws and ordinary screws

Optional: Lock and key

LED Indicators

1 LED status indicator

Relevant Standard

Wi-Fi Alliance Certification


Safety Standard

GB4943, EN/IEC 60950-1

EMC Standard

GB9254, EN301 489

Health Standard

EN 62311

Radio Standard

EN300 328, EN301 893

Vibration Standard

IEC60068-2-31, ETSI EN300 019,



Dimensions (W x D x H) (mm)

116 × 86 × 42




Work Environment


Operating Temperature: -10°C to 45°C

Storage Temperature: -40°C to 70°C


Operating Humidity: 10% to 95% (non-condensing)

Storage Humidity: 5% to 95% (non-condensing)

Installation Mode

Standard 86-type faceplate installation



RG-MACC Cloud Deployment

RG-MACC Solution Architecture

As the RG-MACC (Managed @ Cloud Center) solution component, the RG-AP130 Wall AP Series is designed for wireless deployment in hotels, offices, residential buildings and settings alike.

The Wall AP Series achieves unified management on cloud through the cloud-based wireless control software (RG-MACC). The cloud controller supports device configuration, upgrade and monitoring in groups. Working with Ruijie RG-MACC Platform, the AP Series enables advertising push to Wi-Fi users and maximizes the marketing values.

The RG-AP130 Aps can integrate with Ruijie RG-MACC that streamlines user authentication and advertising push. Social community authentication via Facebook, Twitter and WeChat is supported to collect customer information for big data analysis.

Compatible with the RG-MACC platform, the RG-AP130 Wall AP Series is able to scale its deployment according to the evolving requirements of networks as shown in the above solution diagram.

4D Hospitality Solution

4D Hospitality Solution

Ruijie helps you to innovate your hotel with a smart network. Our 4D Hospitality Solution features ubiquitous Wi-Fi, robust backbone, Layer 7 security protection and unified management to transform your hotel network into a revenue-generating asset with a competitive edge.

The AP130 Wall AP Series can be deployed in hotel rooms. The mini-sized wall-mountable AP has the same size as a standard 86-type faceplate with integrated Ethernet and VoIP ports. Featuring a compact design and easy deployment, the AP enables zero disruption to the interior finishes and offers the best solution for scenarios with delicate interior design. This breaks through traditional wireless network construction methods by reusing existing network cables and minimizes the impact of network construction in hotels or similar settings. As no additional cabling is required, the Wall AP delivers maximum business agility and investment protection.

Smart Aps can be deployed in the corridors and public areas to provide wireless access. The whole network can be centrally managed via the on-premises hardware WLAN controller and Ruijie’s network management software RG-SNC or another option can be to manage the whole network using Ruijie’s RG-MACC Managed Cloud Solution to unify management and configuration of Aps, switches and gateway devices, reducing the total cost of investment while ensuring high usability.





Wall-mounted Wireless AP, standard size of 86-type faceplate, built-in antenna, support concurrent 802.11a/n/ac and 802.11b/g/n, 2 spatial streams, supports 802.11ac Wave 2, supports MU-MIMO, FAT/FIT mode, PoE power supply (PoE adapter sold separately) or local DC power supply, standard package



Ruijie Networks websites use cookies to deliver and improve the website experience.

See our cookie policy for further details on how we use cookies and how to change your cookie settings.

Cookie Manager

When you visit any website, the website will store or retrieve the information on your browser. This process is mostly in the form of cookies. Such information may involve your personal information, preferences or equipment, and is mainly used to enable the website to provide services in accordance with your expectations. Such information usually does not directly identify your personal information, but it can provide you with a more personalized network experience. We fully respect your privacy, so you can choose not to allow certain types of cookies. You only need to click on the names of different cookie categories to learn more and change the default settings. However, blocking certain types of cookies may affect your website experience and the services we can provide you.

  • Performance cookies

    Through this type of cookie, we can count website visits and traffic sources in order to evaluate and improve the performance of our website. This type of cookie can also help us understand the popularity of the page and the activity of visitors on the site. All information collected by such cookies will be aggregated to ensure the anonymity of the information. If you do not allow such cookies, we will have no way of knowing when you visited our website, and we will not be able to monitor website performance.

  • Essential cookies

    This type of cookie is necessary for the normal operation of the website and cannot be turned off in our system. Usually, they are only set for the actions you do, which are equivalent to service requests, such as setting your privacy preferences, logging in, or filling out forms. You can set your browser to block or remind you of such cookies, but certain functions of the website will not be available. Such cookies do not store any personally identifiable information.

Accept All

View Cookie Policy Details

Contact Us

Contact Us

How can we help you?

Contact Us

Get an Order help

Contact Us

Get a tech support