Home> Support> Technical Documents>

RG-WLAN Implementation Cookbook (V3.2)

2017-05-05View: 830
Catalog
11.x项目配置指南模板

         Product Introduction

1.1        System Management

Default Settings

ACNo default IP address.

APDefault IP address is 192.168.110.1(or 192.168.1.1), and both console & telnet password are "admin", default enable password is "apdebug"

 

Following wall AP have different default settings

AP120-W

In Fit mode, IP address of both LAN port and Uplink port IP are 192.168.110.1/24

In Fat mode, IP address of LAN port is 192.168.111.1/24; IP address of Uplink port is 192.168.110.1/24

AP110-W

IP address of Rear panel is 192.168.110.1/24

IP address of Front panel is 192.168.111.1/24

 

1.1.1       Console Management

Connect cables as below diagram

 

Cables

console cable, USB to RS232 cable 

 

 

 

 

 

Putty

Open software Putty, set baud rate to 9600

 

1.1.2       Telnet Management

I. Network Topology

 

II. Configuration Steps

Configuring Telnet& enable password on AC

Ruijie>enable

Ruijie#configure terminal

Ruijie(config)#interface vlan 1 

Ruijie(config-if-vlan 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie

Ruijie(config-line)#login

Ruijie(config)#enable password ruijie

 

Configuring Telnet & Enable password on AP

Console connect to device and set passwords, default ap-mode is fit.

User Access Verification

Password:                                              default password is "ruijie"

Ruijie>

Ruijie>enable

Password:                                             default password is "apdebug"

Ruijie#configure terminal

Ruijie(config)#interface bvi 1

Ruijie(config-if-bvi 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config-if-bvi 1)#interface gigabitEthernet 0/1

Ruijie(config-if-GigabitEthernet 0/1)#encapsulation dot1Q 1

%Warning: Remove all IP address.

Ruijie(config-if-GigabitEthernet 0/1)#exit

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2 

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie

Ruijie(config-line)#login

Ruijie(config)#enable password ruijie

 

Note: when ap-mode change from fit to fat, the default password changes as follow:

User Access Verification

Password:                                              default password is "admin"

Ruijie>

Ruijie>enable

Password:                                              no default password

Ruijie#configure terminal

 

III. Verification

 

Save configuration

Ruijie(config)#end

Ruijie#write

 

Note:

windows7&8 telent client function is not enabled by default, you need to enable the telnet functionality.

Taking Windows 7 as an example:

Control panel - procedures and functions - to open or close the windows function - check the telnet client - select "to determine"

 

1.1.3       SSH Management

I. Network Topology

 

II. Configuration Steps

Configuring SSH on AC

Ruijie>enable

Password:

Ruijie#configure terminal         

Ruijie(config)#enable service ssh-server    

Ruijie(config)#crypto key generate dsa        

Choose the size of the key modulus in the range of 360 to 2048 for your

Signature Keys. Choosing a key modulus greater than 512 may take

a few minutes.

How many bits in the modulus [512]:                

% Generating 512 bit DSA keys. ..[ok]

Ruijie(config)#interface vlan 1  

Ruijie(config-if-VLAN 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.2

Ruijie(config)#enable password ruijie

 

Method 1Login with password

Ruijie(config)#line vty 0 4

Ruijie(config-line)#password ruijie      

Ruijie(config-line)#login                          

Ruijie(config-line)#end                                                 

Ruijie#write   

Building configuration...

[OK]

Ruijie#                                                               

 

Method 2Login with username & password

Ruijie(config)#line vty 0 4       

Ruijie(config-line)#login local                                

Ruijie(config-line)#exit

Ruijie(config)#username admin password ruijie        

Ruijie(config)#end    

Ruijie#write      

Building configuration...

[OK]

Ruijie#        

 

III. Verification

Open Putty, choose Connection type "SSH", input IP address.                                                 

 

 

    To display SSH service status, execute following commands

      

 

1.1.4       Web Management

I. Network Topology

 

 

II. Configuration Steps

Configuring WEB GUI on AC

Ruijie#configure terminal       

Ruijie(config)#enable service web-server 

Ruijie(config)#vlan 1   

Ruijie(config-vlan)#interface vlan 1      

Ruijie(config-if-VLAN 1)#ip address 192.168.1.1 255.255.255.0

Ruijie(config-if-VLAN 1)#exit

Ruijie(config)#webmaster level ?

  <0-2>  Web auth privilege level (0 is the highest level)

Ruijie(config)#webmaster level 0 username ruijie password ruijie

Ruijie(config)#ip route 0.0.0.0 0.0.0.0 192.168.1.254

Note:

1.       AM5528 does not support web management.

2.       Only user “admin” and “ruijie” could be created on cli page, for other account, If you have the web management requirements, please create it on web interface, relative err prompt are shown as follow:

 

III. Verification

Visit web GUI at http://192.168.1.1, it is recommended that access WEB GUI with IE 8.0 and above version in compatible mode.

 

 

1.1.5       Forget IP Address of Wall AP

If administrator forgot IP address of Wall-AP, and do not want to recover factory setting, follow below steps:

1. Power on AP, and connect AP as below diagram:

2. Open packet capture tool, here take Wireshark as example:

         

3.       Check ARP packets, and 192.168.51.54 is correct IP

 

4.       Try to telnet AP

 

5.       If above method doesn't work, suggest to restore factory default.

 

1.2        Firmware Upgrade

1.2.1 Upgrade for RGOS 11.x

1.2.1.1       Upgrade AC & Fit AP (for 11.X)

I. Network Topology

 

II. Requirements

 

1.       Visit official website at www.ruijienetworks.com to request firmware.

 

2.       Run TFTP Server, and put AP&AC firmware in the same folder. Here take Ruijie TFTPServer as example.

 

 TFTP Server should be able to communicate with AC.

3. AC has built CAPWAP tunnel with APs

4. Read Release Note carefully, pay attention to the "upgrade file"

5. DO NOT restart or POWER OFF AC&AP during upgrades.

6. Login AC CLI via console, telnet or SSH.

 

III. Configuration Steps

Upgrading AC

AttentionIn hot-backup scenario, please remove all networks cables on ACs in case of synchronization issue caused by inconsistent firmware.

1.       Display current firmware version and backup relative configuration files.

Ruijie# copy flash:config.text tftp://192.168.1.100/config.text --->backup the configuration files of AC to TFTP Server.

Ruijie# copy flash:ap-config.text tftp://192.168.1.100/ap-config.text ---> backup the configuration of AP to TFTP Server.

 

Ruijie#show version detail

System description     : Ruijie 10G Wireless Switch(WS6008) By Ruijie Networks.

System uptime          : 0:02:15:24

System hardware version: 1.0

System software version: AC_RGOS 11.1(5)B80P3, Release(04131820)

System patch number    : NA

System software number : M20361001182017

System serial number   : 1234942570002

System boot version    : 2.0.19.97cfa98(161210)

System core version    : 2.6.32.355270930a6bde

System cpu partition   : 4-11

 

2.       Transfer new firmware to AC, execute below commands:

Ruijie#upgrade download tftp://192.168.1.100/rgos.bin

 

III. Verification

After reloading, execute command "show version" to verify firmware version.

Ruijie#show version detail

System description     : Ruijie 10G Wireless Switch(WS6008) By Ruijie Networks.

System uptime          : 0:02:15:24

System hardware version: 1.0

System software version: AC_RGOS 11.1(5)B80P3, Release(04131820)

System patch number    : NA

System software number : M20361001182017

System serial number   : 1234942570002

System boot version    : 2.0.19.97cfa98(161210)

System core version    : 2.6.32.355270930a6bde

System cpu partition   : 4-11

 

Upgrading Fit APs
Attention
Generally, the fit ap and ac can work normally only when the versions of them are consistent

1.       Display current ap firmware version on AC, execute commands "show version all"

Ruijie#show version detail

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1969-12-31 23:59:59

System uptime: 0:00:01:09

System hardware version: 1.10    ------>hardware version

System software version: AP_RGOS 11.1(5)B3, Release(02160403)------>software version

System patch number    : NA

System software number : M03112104042015

System serial number: G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.ab930e7d22374b   

 

2.       To transfer AP new firmware to AC,  execute below commands:

Ruijie#copy tftp://192.168.1.100/330.bin flash:330.bin

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Copy success

 

3.       To configure ap-serial,  execute below commands:

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file flash:330.bin

Ruijie(config-ac)#ap-image auto upgrade

 

4.       After AP reloading, APs will establish CAPWAP tunnel with AC.

 

III. Verification

1.       Display AP upgrading progress,  execute commands "show ap-config updating-list"

Ruijie#show ap-config updating-list

AP NAME                                  AP PID          File Tx                  Time               AP Reset Ready

----------------------           ---------------     --------               ------------     -----------

AP330-I                                  AP330-I          20 %                 00:00:06               N

 

2.       Display current ap firmware version on AC,  execute commands "show version all"

Ruijie>show version     

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1970-01-01 00:00:01

System uptime: 0:00:01:52

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B5, Release(02182520)

System patch number    : NA

System serial number: G1GDB16019485

System boot version    : 1.1.1

 

1.2.1.2       Upgrade Fat AP (for 11.X)

I. Network Topology

 

 

        

 

II. Requirements

1.       Visit official website at www.ruijienetworks.com to request firmware.

 

2.       Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

TFTP Server should be able to communicate with AP.

 

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

 

Attention: Wall APs, like AP130 (W2) & AP130L, do not have console port. See Device Management -->Conventions to learn the default IP address.

 

III. Configuration Steps

Upgrading FAT APs

 

1.       Backup configuration files to TFTP Server, and display current firmware version

Ruijie#copy flash:config.text tftp://192.168.1.100/config.text --->backup configuration files of AP to TFTP Server

 

Ruijie#show version detail  ---> check version

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1969-12-31 23:59:59

System uptime: 0:00:01:09

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B3, Release(02160403)

System patch number    : NA

System software number : M03112104042015

System serial number   : G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.ab930e7d22374b

 

2.       Display current ap mode

AP320#show ap-mode

current mode: fat

AP320#

 

3.       Transfer new firmware to AP,  execute below commands:

Ruijie#upgrade download tftp://192.168.1.100/330-b5.bin

Upgrade the device must be auto-reset after finish, are you sure upgrading now?[Y/n]y

Running this command may take some time, please wait.

Please wait for a moment......

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!.!!!!!!!!!.!!!

 

Begin to upgrade the install package 330-b5.bin...   --->reload automatically

*Jan  1 00:03:52: %7: Upgrade processing is 10%

Uncompress file 330-b5.bin. .......

 

IV. Verification

After reloading,  execute command "show version"  to verify firmware version.

Ruijie#show version  detail

System description     : Ruijie Indoor AP330-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1970-01-01 00:00:01

System uptime: 0:00:01:09

System hardware version: 1.10

System software version: AP_RGOS 11.1(5)B5, Release(02182520)

System patch number    : NA

System software number : M20085306252015

System serial number   : G1GDB16019485

System boot version    : 1.1.1.6822c2a(140920)

System core version    : 2.6.32.720c78d1a03d63

 

1.2.2       Upgrade from RGOS 10.x to 11.x

 

1.2.2.1        Upgrade AC & Fit AP from 10.X to 11.X

I. Network Topology

 

         

II. Requirements

1.       Visit official website at www.ruijienetworks.com to request firmware..

 

2.       Run TFTP Server, and put AP&AC firmware in the same folder. Here take Ruijie TFTPServer as example.

 

 TFTP Server should be able to communicate with AC.

3. AC has built CAPWAP tunnel with APs

4. Read Release Note carefully, pay attention to the "upgrade file"

5. DO NOT restart or POWER OFF AC&AP during upgrades.

6. Login AC CLI via console, telnet or SSH.

 

III. Configuration Steps

Upgrading AC

AttentionIn hot-backup scenario, please remove all networks cables on ACs in case of synchronization issue caused by inconsistent firmware.

1.       Display current firmware version and backup relative configuration files.

Ruijie#copy flash:config.text tftp://172.18.158.204/config.text --->backup the configuration files of AC to TFTP Server.

Ruijie#copy flash:ap-config.text tftp://172.18.158.204/ap-config.text ---> backup the configuration of AP to TFTP Server.

 

 

2.       Transfer new firmware to AC,  execute below commands:

Ruijie#copy tftp://172.18.158.204/AC_RGOS10.x_TO_11.x(Mid)_G1C5-01_02172111.bin flash:rgos.bin

 

After reloading, execute command "show version" to verify firmware

 

3.       Because the configuration files will lost when upgrade to mid version, need to import the config.text, and test the connection between AC and terminal, then Downgrade AC to target version 11.x

Ruijie#upgrade download tftp://192.168.1.100/AC_RGOS11.1(5)B8_G1C5-01_03151003_install.bin

 

IV. Verification

 

       After reloading, execute command "show version" to verify firmware version

 

 

Upgrading Fit APs

1.       Transfer 11.x and mid version of AP to AC,  execute below commands:

Ruijie#copy tftp://172.18.158.204/AP_RGOS10.x_TO_11.x(Mid)_S2C3-01_02201910.bin flash:ap530-mid.bin

Ruijie#copy tftp://172.18.158.204/AP_RGOS11.1(5)B8_S2C3-01_03151007_install.bin flash:ap530.bin

 

2.       To configure ap-serial,  execute below commands:

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file ap530-mid.bin   rgos10

Ruijie(config-ac)#active-bin-file ap530.bin

Ruijie(config-ac)#ap-serial ap530 AP530-I hw-ver 1.x 

Ruijie(config-ac)#ap-image ap530-mid.bin ap530

Ruijie(config-ac)#ap-image ap530.bin ap530

 

IV. Verification

1.       After reloading, execute command "show version" to verify firmware version

 

2.       After AP reloading, APs will build CAPWAP tunnel with AC.

 

1.2.2.2       Upgrade Fat AP from 10.X to 11.X

I. Network Topology

        

 

II. Requirements

1.       Visit official website at www.ruijienetworks.com to request firmware.

2.       Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

 

TFTP Server should be able to communicate with AP.

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

 

Attention: Upgrade from 10.X to 11.X, configuration will lost, backup the configuration before downgrading; need to downgrade to mid version first.

 

III. Configuration Steps

Upgrading FAT APs

1.       Backup configuration files to TFTP Server, and display current firmware version

Ruijie#copy flash:config.text tftp://192.168.111.2/config.text --->backup configuration files of AP to TFTP Server

 

 

2.       Display current ap mode

Ruijie#show ap-mode

current mode: fat

 

3.       Transfer new firmware to AP,  execute below commands:

Ruijie#copy tftp://192.168.111.2/AP_RGOS10.x_TO_11.x(Mid)_S2C3-01_02201910.bin flash:rgos.bin

Upgrade the device must be auto-reset after finish, are you sure upgrading now?[Y/n]y

Running this command may take some time, please wait.

Please wait for a moment......

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

 

Verification

 

4.       downgrade to target version 11.x

Ruijie# upgrade download tftp://192.168.111.2/AP_RGOS11.1(5)B8_S2C3-01_03151007_install.bin

 

5.        reload and verification

 

1.2.3       Downgrade from RGOS 11.x to 10.x

1.2.3.1       Downgrade the AC & Fit AP from 11.X to the 10.X

I. Network Topology

 

        

II. Requirements

1.       Visit official website at www.ruijienetworks.com to request firmware.

2.       Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

 

 TFTP Server should be able to communicate with AP.

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

 

Attention: Downgrade from 11.X to 10.X, configuration will lost, backup the configuration before downgrading; need to downgrade to mid version first.

 

III. Configuration Tips

Downgrading FIT APs

1.       Backup configuration files on ac

2.       Transfer mid version of AP to AC

TFTP Server should be able to communicate with AC.

3.       Active version of AP

4. Read Release Note carefully, pay attention to the "downgrade file"

5. DO NOT restart or POWER OFF AC&AP during upgrades.

6. Login AC CLI via console, telnet or SSH.

 

IV. Configuration Steps

Downgrading AC

AttentionIn hot-backup scenario, please remove all networks cables on ACs in case of synchronization issue caused by inconsistent firmware.

1.       Display current firmware version

 

Downgrading Fit APs
1.  To transfer AP new firmware to AC, execute below commands:

Ruijie#copy tftp://192.168.1.100/AP_RGOS11.1(2)B1_AP320_v2.0_degrade.bin flash:320-mid.bin

 

2         To configure ap-serial,  execute below commands:

Ruijie#config terminal

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file 320-mid.bin

Ruijie(config-ac)#ap-serial ap320 AP320-I hw-ver 1.x

Ruijie(config-ac)#ap-image ap320-mid.bin ap320

Ruijie(config-ac)#end

Ruijie#wr

 

2.       telnet APs and verify the current version

Ruijie#show version

System description     : Ruijie Indoor AP320-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 1970-01-01 0:0:0

System uptime: 0:0:0:44

System hardware version: 1.10

System software version: RGOS 10.4(1b19)p2, Release(175879)

System boot version    : 10.4.155446(Master), 10.4.155446(Slave) -àmid version of AP

System serial number   : G1GDC13025434

 

3.       Downgrade AC from 11.X to 11.X_to_10.X(Mid),  execute below commands:

Ruijie#upgrade download tftp://172.18.158.204/AC_RGOS11.x_TO_10.x(Mid)_G1C5-02_02172016.bin force

 

Verification

After reloading, execute command "show version" to verify firmware

       

4.       Because the configuration files will lost when downgrade to mid version, need to import the config.text, and test the connection between AC and terminal, then Downgrade AC to target version 10.x

Ruijie#copy tftp://172.18.158.205/WLAN-AC-50XX_10.4(1b19)p2_R179742.bin flash:rgos.bin

Ruijie#reload

 

     Verification

     

 

5.       After downgrading the AC, the configuration will loss, need to import the ac configuration.

Ruijie#copy tftp://192.168.1.100/config.text flash:config.text

Ruijie#copy tftp://192.168.1.100/ap-config.text flash:ap-config.text

Ruijie#reload 

 

6.       Downgrade AP to target version 10.x

Ruijie#copy tftp://192.168.1.100/AP320_10.4(1b19)p2_R179742.bin flash 320I.bin

Ruijie#configure terminal

Ruijie(config)#ac-controller

Ruijie(config-ac)#active-bin-file 320I.bin

Ruijie(config-ac)#ap-serial ap320 AP320-I hw-ver 1.x

Ruijie(config-ac)#ap-image 320I.bin ap320

Ruijie(config-ac)#end

Ruijie#wr

 

V. Verification    

Ruijie#show version

System description     : Ruijie Indoor AP320-I (802.11a/n and 802.11b/g/n) By Ruijie Networks.

System start time      : 2015-01-05 12:37:41

System uptime: 4:0:24:8

System hardware version: 1.10

System software version: RGOS 10.4(1b19)p2, Release(179742)

System boot version    : 10.4.155446(Master), 10.4.155446(Slave)

System serial number   : G1GD91300419A

 

1.2.3.2       Downgrade the Fat AP from 11.X to the 10.X

I. Network Topology

 

        

II. Requirements

1.       Visit official website at www.ruijienetworks.com to request firmware.

2.       Run TFTP Server, and put AP firmware in the same folder. Here take Ruijie TFTPServer as example.

 

TFTP Server should be able to communicate with AP.

3. Read Release Note carefully, pay attention to the "upgrade file"

4. DO NOT restart or POWER OFF AP during upgrades.

5. Login AP CLI via console, telnet or SSH.

 

Attention: Downgrade from 11.X to 10.X, configuration will lost, backup the configuration before downgrading; need to downgrade to mid version first.

 

III. Configuration Steps

Downgrading FAT APs

1.       Backup configuration files to TFTP Server, and display current firmware version

Ruijie#copy flash:config.text tftp://192.168.111.2/config.text --->backup configuration files of AP to TFTP Server

 

 

2.       Display current ap mode

Ruijie#show ap-mode

current mode: fat

 

3.       Transfer new firmware to AP, execute below commands:

Ruijie#upgrade download tftp://192.168.111.2/AP_RGOS11.x_TO_10.x(Mid)_S2C3-01_02180712.bin

Upgrade the device must be auto-reset after finish, are you sure upgrading now?[Y/n]y

Running this command may take some time, please wait.

Please wait for a moment......

Press Ctrl+C to quit

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

*Jan  1 00:04:27: %7:

*Jan  1 00:04:27: %7: Begin to upgrade the install package AP_RGOS11.x_TO_10.x(Mid)_S2C3-01_02180712.bin...

*Jan  1 00:04:27: %7: Upgrade processing is 10%

RG-UPGRADE:package.c:621]Old md5 value(/rootfs.ubi):

[RG-UPGRADE:rpm_opt.c:374]:e2d4e747428247db1ca518ade88d0bb1

 

Verification

 

4.       downgrade to target version 10.x

Ruijie#copy tftp://192.168.111.2/AP530-PPC_10.4(1b19)p2_R179742.bin flash:rgos.bin

 

5.       reload and verification

 

1.2.4       Recover Firmware under BOOT

1.2.4.1       AC & AP with Console Port

I. Network Topology

 

II. Requirements

1. Generally, we recover firmware under BOOT mode if we deletes firmware on Main Mode by mistake, firmware broken or any other unknown reasons that devices cannot boot up and enter Main Mode.

2. Finish reading Device Management --> System Management --> Firmware Upgrade, have knowledge of how to transfer firmware with TFTP server.

3. It's applicable for both AC and APs with console port. Not applicable for Wall APs without console port.

Note: remember to turn off Windows Defender protection.

 

III. Configuration Steps

1.       Restart devices,   press "CTRL + C"  when system prompts,  enter BOOT Mode, Input 0

2.       Input 1, then upgrade firmware with the following steps.

3. Input "yes"   

 

4. Press "CTRL+Z" return to upper level, then choose "2" to run main

 

IV. Verification

Devices succeed to enter Main mode, execute command "show version", check the firmware version.

Ruijie#show version

 

1.2.4.2       Wall AP without Console Port

I. Network Topology

 

 

II. Requirements

1. Generally, we recover firmware under BOOT mode if we deletes firmware on Main Mode by mistake, firmware broken or any other unknown reasons that devices cannot boot up and enter Main Mode.

2. Finish reading Device Management --> System Management & --> Firmware Upgrade, have knowledge of how to transfer firmware with TFTP server.

        

III. Configuration Steps

1.       Open Wireshark, load a packet capture process as below.  AP 192.168.64.163 lost firmware and is requesting 192.168.64.1 for firmware.

 

2.  Assign IP address 192.168.64.1 to laptop, enable TFTP Server and also prepare the firmware.

 

2.       Edit a notepad name as "FileList.txt", put it in the same folder as shown above,   the content is the firmware name you're going to transfer

4. AP will begin downloading firmware soon, verify by viewing TFTP Server connection status.

5. AP will reload when finish recovering firmware

 

IV. Verification

Login AP via telnet and AP is recovered.

1.3        Password Recovery

1.3.1       Recover AC &Fat AP password

I. Network Topology

 

II. Requirements

1. Finish reading System Management --> Console Management.

2. Login AC CLI via Console.

 

III. Configuration Steps

Recovering AC password (configuration file remains)

1. Power off AC, then power up.

2. Press CTRL + C, enter CTRL mode.

 

3. Input CTRL+Q, enter uboot mode. And then input "main_config_password_clear"

 

4. Device will reload automatically.

 

3.       When finish reloading, enter CLI without input password.

Note: The default timeout period is 10min. Please change your password before time out.

 

4.       Change password, and then use the command “wr” to save your configuration.

 

5.       save configuration

 

Re-login AC, execute commands "show runing-config" to check configurations.

 

1.4        Restore Factory Default

1.4.1       Restoring AC & FAT AP

I. Requirements

1. Finish reading Device Management --> System Management

2. Login CLI via console, telnet or SSH

 

II. Configuration Steps

Execute command "dir" to check file system

Ruijie#dir

    Mode Link      Size               MTime Name

-------- ---- --------- ------------------- ------------------

            1      1600 1970-01-02 01:31:10 config.text

            1     11729 2015-06-18 02:03:26 cw_teardown_info.txt

   <DIR>    1         0 1970-01-01 00:00:00 dev/

            1        33 2015-06-03 00:04:25 dhcp_bind.dat

   <DIR>    4         0 1970-01-01 00:00:18 pkistore/

   <DIR>    5         0 1970-01-01 00:00:11 portal/

   <DIR>    0         0 1970-01-01 00:00:00 proc/

   <DIR>    1         0 1970-01-01 00:00:01 ram/

            1      1529 2015-03-09 16:31:28 reset.txt

            1   8359680 2015-03-09 16:31:26 rgos.bin

   <DIR>    2         0 1970-01-01 00:00:08 tmp/

            1    150740 1970-01-01 00:00:12 ucs_big5.db

            1    239708 1970-01-01 00:00:12 ucs_gb.db

   <DIR>    4         0 1970-01-01 00:00:12 web/

            1   2766752 1970-01-01 00:00:10 web_management_pack.upd

--------------------------------------------------------------

12 Files (Total size 12243866 Bytes), 7 Directories.

Total 132120576 bytes (126MB) in this device, 115515392 bytes (110MB) available.

 

"config.text" is configuration file, execute commands "del config.text" to set factory default

Ruijie#del config.text

Are you sure you want to delete "config.text"?[Yes/No]y 

Ruijie#reload

Processed with reload? [no]y

 

After reloading, execute commands "show running-config" to check configuration.

 

1.4.2       Restoring FIT AP

I. Requirements

1. Finish reading Device Management --> System Management

2. Login CLI via console, telnet or SSH

 

 

II. Configuration Steps

Restore Factory Default

AC#conf t

AC(config)#ac-controller

AC(config-ac)#reset ?

all     Reset the all APs in this AC.

single  Reset the single ap.

 

Then the fit ap will restart automatically.

 

III. Verification

After reloading, execute commands "show running-config" to check configuration.

 

1.4.3       Restoring WALL AP & AP3220-P

Especially, for Wall AP including AP110W, AP120W, AP130W

Long press "reset" button more than 8 seconds to set factory default.

 

Especially, for AP3220-P

    Directly short circuiting the console port and LAN2 port, when the equipment indicator light turns green, the device is returned to the factory successfully, then pull off the short cable.

 

1.5        Backup Configuration

1.5.1       Backup to Flash

I. Requirements

1. Finish reading System Management

2. Login device CLI via Console, telnet or SSH.

 

II. Configuration Steps

Execute command "dir" to check file system

WS6008#dir

Directory of flash:/

Number  Properties   Size               Time                    Name

------  ----------  ------    ------------------------  --------------------

  1       drwx      160B      Mon Oct 10 19:27:37 2016  dev                

  2       drwx      160B      Mon Mar 21 17:32:15 2016  rep                

  3       drwx      224B      Mon Mar 21 17:32:16 2016  var                

  4       drwx      160B      Mon Oct 10 19:27:40 2016  addr               

  5       -r--      4.1k      Wed Nov  2 16:27:00 2016  tmp_env.txt        

  6       -rwx      5.0k      Mon Mar 21 17:32:36 2016  hwd.db             

  7       -rw-      2.9k      Tue Oct 11 12:39:39 2016  virtual_switch.text

  8       drwx      304B      Mon Mar 21 17:32:42 2016  security           

  9       -rwx      180B      Fri Nov  4 16:48:45 2016  config_vac.dat     

 10       -rw-      14.8k     Fri Nov  4 16:48:46 2016  config.text        

 11       -rwx      384B      Thu Sep 29 10:21:54 2016  LIC-WLAN-AP-3200000003956646.lic

 12       -rwx      18B       Mon Sep 26 17:35:26 2016  test.txt           

 13       -rw-      718B      Tue Oct 11 09:14:18 2016  ap-standalone.text 

 14       -rwx      696B      Mon Mar 21 17:32:30 2016  httpd_cert.crt     

 15       -rwx      21B       Fri Nov  4 16:48:45 2016  syslog_rfc5424_flag.txt

 16       drwx      424B      Tue Mar 29 16:50:43 2016  portal             

 17       -rwx      44.4M     Mon Oct 31 18:20:17 2016  AM_RGOS11.1(5)B9_G1B5-01_03211300_install.bin

 18       -rwx      620B      Tue Oct 11 12:39:27 2016  rsa_private.bin    

 19       -rwx      336B      Sun Oct 30 15:32:36 2016  dsa_private.bin    

 20       -rw-      5.8k      Thu Jun 30 14:35:03 2016  text.bak           

 21       -rwx      384B      Wed Oct 12 17:17:05 2016  LIC-WLAN-AP-3200000003466646.lic

 22       drwx      296B      Thu Oct 13 13:45:02 2016  upgrade            

 23       drwx      160B      Fri Nov  4 09:36:26 2016  tech_vsd0          

 24       drwx      448B      Thu Sep 29 11:24:06 2016  rg_licns           

 25       drwx      312B      Mon Oct 10 19:57:36 2016  syslog             

 26       -rw-      147B      Tue Oct 11 12:39:39 2016  ap-virtual_switch.text

 27       -rw-      723B      Fri Nov  4 16:48:46 2016  ap-config.text     

 28       -rwx      187.1k    Fri Nov  4 18:27:03 2016  log-13-may-5.txt   

 29       -rwx      77.8M     Mon Oct 31 20:23:11 2016  AC_RGOS11.1(5)B9_G2C6-01_03201812_install.bin.up.tmp

 30       -rwx      887B      Mon Mar 21 17:32:30 2016  httpd_key.pem      

 31       -rw-      8.9k      Tue Oct 11 09:14:18 2016  standalone.text    

21 files, 10 directories

281,903,104 bytes data total (155,267,072 bytes free)

536,870,912 bytes flash total (155,267,072 bytes free)

 

"config.text" is configuration file, execute commands "copy flash:config.text flash:config.bak" to backup configuration file

"ap-config.text" is ap configuration file, execute commands "copy flash:ap-config.text flash:ap-config.bak" to backup ap configuration file

Ruijie#

Ruijie#copy flash:config.text flash:config.bak

Ruijie#copy flash:ap-config.text flash:ap-config.bak

 

III. Verification

To view backup file, execute command "dir" to display filesystem. The file size should match.

WS6008#dir

Directory of flash:/

Number  Properties   Size               Time                    Name

------  ----------  ------    ------------------------  --------------------

  1       drwx      160B      Mon Oct 10 19:27:37 2016  dev                

  2       drwx      160B      Mon Mar 21 17:32:15 2016  rep                 

  3       drwx      224B      Mon Mar 21 17:32:16 2016  var                

  4       drwx      160B      Mon Oct 10 19:27:40 2016  addr               

  5       -r--      4.1k      Wed Nov  2 16:27:00 2016  tmp_env.txt        

  6       -rwx      5.0k      Mon Mar 21 17:32:36 2016  hwd.db             

  7       -rw-      2.9k      Tue Oct 11 12:39:39 2016  virtual_switch.text

  8       drwx      304B      Mon Mar 21 17:32:42 2016  security           

  9       -rwx      180B      Fri Nov  4 16:48:45 2016  config_vac.dat     

 10       -rw-      14.8k     Fri Nov  4 16:48:46 2016  config.text        

 11       -rwx      384B      Thu Sep 29 10:21:54 2016  LIC-WLAN-AP-3200000003956646.lic

 12       -rwx      18B       Mon Sep 26 17:35:26 2016  test.txt           

 13       -rw-      718B      Tue Oct 11 09:14:18 2016  ap-standalone.text 

 14       -rwx      696B      Mon Mar 21 17:32:30 2016  httpd_cert.crt     

 15       -rwx      21B       Fri Nov  4 16:48:45 2016  syslog_rfc5424_flag.txt

 16       drwx      424B      Tue Mar 29 16:50:43 2016  portal             

 17       -rwx      44.4M     Mon Oct 31 18:20:17 2016  AM_RGOS11.1(5)B9_G1B5-01_03211300_install.bin

 18       -rwx      620B      Tue Oct 11 12:39:27 2016  rsa_private.bin    

 19       -rwx      336B      Sun Oct 30 15:32:36 2016  dsa_private.bin    

 20       -rw-      14.8k     Fri Nov  4 19:08:10 2016  config.bak         

 21       -rw-      5.8k      Thu Jun 30 14:35:03 2016  text.bak           

 22       -rwx      384B      Wed Oct 12 17:17:05 2016  LIC-WLAN-AP-3200000003466646.lic

 23       drwx      296B      Thu Oct 13 13:45:02 2016  upgrade            

 24       drwx      160B      Fri Nov  4 09:36:26 2016  tech_vsd0          

 25       drwx      448B      Thu Sep 29 11:24:06 2016  rg_licns           

 26       -rw-      723B      Fri Nov  4 19:08:21 2016  ap-config.bak      

 27       drwx      312B      Mon Oct 10 19:57:36 2016  syslog             

 28       -rw-      147B      Tue Oct 11 12:39:39 2016  ap-virtual_switch.text

 29       -rw-      723B      Fri Nov  4 16:48:46 2016  ap-config.text     

 30       -rwx      187.1k    Fri Nov  4 18:27:03 2016  log-13-may-5.txt   

 31       -rwx      77.8M     Mon Oct 31 20:23:11 2016  AC_RGOS11.1(5)B9_G2C6-01_03201812_install.bin.up.tmp

 32       -rwx      887B      Mon Mar 21 17:32:30 2016  httpd_key.pem      

 33       -rw-      8.9k      Tue Oct 11 09:14:18 2016  standalone.text    

23 files, 10 directories

281,903,104 bytes data total (155,394,048 bytes free)

536,870,912 bytes flash total (155,394,048 bytes free)

 

Tips: To read text file in CLI, exeute command "more config.bak"

WS6008#more config.bak

version AC_RGOS 11.1(5)B9, Release(03201812)

hostname WS6008

!

wlan-config 1 cmcp

 ssid-code utf-8

!

wlan-config 2 Eweb_BA832

 ssid-code utf-8

 band-select enable

 schedule session 2

!

wlan-config 3 Eweb_BA833

 ssid-code utf-8

!

wlan-config 4 oversea123

 ssid-code utf-8

!

wlan-config 5 Eweb_BA835

 ssid-code utf-8

!

wlan-config 13 test-for-sec

!

wlan-config 55 AM5528

 band-select enable

1.5.2       Backup to TFTP Server

I. Network Topology

 

        

II. Requirements

1. Finish reading System Management

2. Login device CLI via Console, telnet or SSH.

3. Run TFTP software in the PCs

3. TFTP Server is able to communicate with device

 

III. Configuration Steps

To copy files in flash to TFTP Server, execute commands "copy flash:config.text tftp:"

Ruijie#copy flash:config.text tftp://192.168.1.100/config.text

 

IV. Verification

The backup configuration file will be copied to TFTP Server.

 

1.6        License Application

Problem: Wireless license import failed.

 

Solution:

1.       Confirm whether the SN is correct via the official website.

 

After login successfully, input authorization code, and then click “search” to check whether the relative device SN is consistent with the practical SN.

 

2.       If the root case is the incorrect SN, unbind the License first

Step1:

Visit official website (http://www.ruijienetworks.com/service/License.aspx ), unbind License files.

 Click "Service" ->"Product Licensing" ->choose "WLAN" for wireless license unbinding. Choose “Unbind License”-> choose “Wireless”-> click “Unbind License”, then click ”Complete” after filling  in product info.

Note: Before unbinding the license files, you should register first if you do not have an account for login.

 

Then in the pop-up dialog box,  click “finish” to submit an application.

 

Step2: After completing the application, submitted it to TAC for application via e-mail account: service_rj@ruijienetworks.com. And then waiting for approval.

Click "Service" ->"Product Licensing" ->choose "WLAN" for wireless license unbinding. Choose “Unbind License”-> choose “Wireless”-> Check the approval status, if approved, customer can apply for a new license with the original S/N.

 

 

Warm prompt:

After unbind the license successfully, if you have the requirement of Wireless License Registration, please follow the following steps to apply for new license.

Step1: Obtain the license register number.

Open the attachment in the Authorization Letter to obtain the Authentication Code..

 

Or obtain the authentication code from the CD. There is a pdf file in the CD which is shown as follow:

 

Step2: Visit the official website, bind License files.

Click "Service" ->"Product Licensing" ->choose "WLAN" for wireless license binding, after filling in the information, click “Complete”, it will jump to the download page of. lic file.

Note: Before binding the license files, you should register first if you do not have an account for login.

 

Step3: Install the authorization document

Note: If the license obtained by user is a. lic file, install the license with the following way

 i) Upload the local license file to the wlc.

 Configuration Example:

Ruijie#copy tftp://192.168.64.2/LIC-WLAN-AP-800000015692434.lic flash:/LIC-WLAN-AP-  800000015692434.lic

Press Ctrl+C to quit

!

Copy success.

 

 

ii) Install license file

 Configuration Example:

Ruijie# license install flash:LIC-WLAN-AP-800000015692434.lic

 Are you sure to install this license[y/n]:y

Success to install license file, service name: LIC-WLAN-AP-8.

 

Step3: Install the authorization document

Note: If the license obtained by user is a license key, install the license with the following way

i) The following shows the similar format of the license obtained by the user

            XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XXXX

Record the generated license key, connect to the wlan-ac device, and use the set license license command. If it prompts it is correct, the register application is successful. If it prompts the error, contact the Ruijie Customer Service center for the related consultation.

 

ii) Configure the License Basic Features

Configuration Example:

Ruijie# configure terminal

Enter configuration commands, one per line. End with CNTL/Z.

Ruijie(config)# set license AAAA-BBBB-CCCC-DDDD-EEEE-FFFF-GGGG-HHHH  

 

Verification

Showing the License Configuration, you could find you have add new license successfully.

Ruijie# show license

 

 

  • Sales Enquiry